 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| DISCRETE SEMICONDUCTORS DATA SHEET BTA204S series D, E and F BTA204M series D, E and F Three quadrant triacs guaranteed commutation Product specification December 1998 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation GENERAL DESCRIPTION Passivated guaranteed commutation triacs in a plastic envelope suitable for surface mounting, intended for use in motor control circuits or with other highly inductive loads. These devices balance the requirements of commutation performance and gate sensitivity. The "sensitive gate" E series and "logic level" D series are intended for interfacing with low power drivers, including micro controllers. BTA204S series D, E and F BTA204M series D, E and F QUICK REFERENCE DATA SYMBOL PARAMETER MAX. MAX. 600D 600E 600F 600 4 25 MAX. UNIT 800E 800F 800 4 25 BTA204S (or BTA204M)- 500D BTA204S (or BTA204M)- 500E BTA204S (or BTA204M)- 500F Repetitive peak 500 off-state voltages RMS on-state current 4 Non-repetitive peak on-state 25 current VDRM IT(RMS) ITSM V A A PINNING - SOT428 PIN Standard Alternative NUMBER S M 1 2 3 tab MT1 MT2 gate MT2 gate MT2 MT1 MT2 PIN CONFIGURATION tab SYMBOL T2 T1 2 1 3 G LIMITING VALUES Limiting values in accordance with the Absolute Maximum System (IEC 134). SYMBOL VDRM IT(RMS) ITSM PARAMETER Repetitive peak off-state voltages RMS on-state current Non-repetitive peak on-state current full sine wave; Tmb 107 C full sine wave; Tj = 25 C prior to surge t = 20 ms t = 16.7 ms t = 10 ms ITM = 6 A; IG = 0.2 A; dIG/dt = 0.2 A/s CONDITIONS MIN. -500 5001 MAX. -600 6001 4 -800 800 UNIT V A It dIT/dt IGM VGM PGM PG(AV) Tstg Tj 2 I t for fusing Repetitive rate of rise of on-state current after triggering Peak gate current Peak gate voltage Peak gate power Average gate power Storage temperature Operating junction temperature 2 - 25 27 3.1 100 2 5 5 0.5 150 125 A A A2s A/s A V W W C C over any 20 ms period -40 - 1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 6 A/s. December 1998 2 Rev 1.000 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation THERMAL RESISTANCES SYMBOL Rth j-mb Rth j-a PARAMETER CONDITIONS BTA204S series D, E and F BTA204M series D, E and F MIN. - TYP. 75 MAX. 3.0 3.7 - UNIT K/W K/W K/W Thermal resistance full cycle junction to mounting base half cycle Thermal resistance pcb (FR4) mounted; footprint as in Fig.14 junction to ambient STATIC CHARACTERISTICS Tj = 25 C unless otherwise stated SYMBOL IGT PARAMETER Gate trigger current 2 CONDITIONS BTA204S (or BTA204M)VD = 12 V; IT = 0.1 A T2+ G+ T2+ GT2- GVD = 12 V; IGT = 0.1 A T2+ G+ T2+ GT2- GVD = 12 V; IGT = 0.1 A IT = 5 A VD = 12 V; IT = 0.1 A VD = 400 V; IT = 0.1 A; Tj = 125 C VD = VDRM(max); Tj = 125 C MIN. TYP. ...D MAX. ...E 10 10 10 12 18 12 12 1.7 1.5 0.5 ...F 25 25 25 20 30 20 20 UNIT 0.25 - 1.4 0.7 0.4 0.1 5 5 5 6 9 6 6 mA mA mA mA mA mA mA V V V mA IL Latching current IH VT VGT Holding current On-state voltage Gate trigger voltage ID Off-state leakage current DYNAMIC CHARACTERISTICS Tj = 25 C unless otherwise stated SYMBOL dVD/dt dIcom/dt PARAMETER Critical rate of rise of off-state voltage CONDITIONS BTA204S (or BTA204M)...D MIN. ...E 30 2.0 ...F 50 2.5 V/s A/ms TYP. MAX. UNIT dIcom/dt tgt VDM = 67% VDRM(max); 20 Tj = 125 C; exponential waveform; gate open circuit Critical rate of change VDM = 400 V; Tj = 125 C; 1.0 of commutating current IT(RMS) = 4 A; dVcom/dt = 20V/s; gate open circuit Critical rate of change VDM = 400 V; Tj = 125 C; 5.0 of commutating current IT(RMS) = 4 A; dVcom/dt = 0.1V/s; gate open circuit Gate controlled turn-on ITM = 12 A; VD = VDRM(max); time IG = 0.1 A; dIG/dt = 5 A/s - - - - A/ms - - 2 - s 2 Device does not trigger in the T2-, G+ quadrant. December 1998 3 Rev 1.000 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation BT136 BTA204S series D, E and F BTA204M series D, E and F IT(RMS) / A BT136 8 7 6 5 4 3 2 1 0 Ptot / W Tmb(max) / C 101 104 5 1 = 180 120 90 60 30 4 107 110 113 116 119 107 C 3 2 1 122 0 1 2 3 IT(RMS) / A 4 125 5 0 -50 0 50 Tmb / C 100 150 Fig.1. Maximum on-state dissipation, Ptot, versus rms on-state current, IT(RMS), where = conduction angle. Fig.4. Maximum permissible rms current IT(RMS) , versus mounting base temperature Tmb. BT136 1000 ITSM / A BT136 IT T ITSM 12 10 time IT(RMS) / A Tj initial = 25 C max 100 dIT /dt limit 8 6 4 T2- G+ quadrant 2 10 10us 100us 1ms T/s 10ms 100ms 0 0.01 0.1 1 surge duration / s 10 Fig.2. Maximum permissible non-repetitive peak on-state current ITSM, versus pulse width tp, for sinusoidal currents, tp 20ms. Fig.5. Maximum permissible repetitive rms on-state current IT(RMS), versus surge duration, for sinusoidal currents, f = 50 Hz; Tmb 107C. VGT(Tj) VGT(25 C) 30 25 20 15 10 5 0 ITSM / A BT136 1.6 IT T I TSM time BT136 1.4 1.2 1 0.8 0.6 0.4 -50 Tj initial = 25 C max 1 10 100 Number of cycles at 50Hz 1000 0 50 Tj / C 100 150 Fig.3. Maximum permissible non-repetitive peak on-state current ITSM, versus number of cycles, for sinusoidal currents, f = 50 Hz. Fig.6. Normalised gate trigger voltage VGT(Tj)/ VGT(25C), versus junction temperature Tj. December 1998 4 Rev 1.000 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation IGT(Tj) IGT(25 C) BTA204S series D, E and F BTA204M series D, E and F BT136 typ max BTA204 12 IT / A Tj = 125 C Tj = 25 C 3 2.5 2 1.5 1 0.5 T2+ G+ T2+ GT2- G- 10 Vo = 1.27 V Rs = 0.091 ohms 8 6 4 2 0 0 -50 0 50 Tj / C 100 150 0 0.5 1 1.5 VT / V 2 2.5 3 Fig.7. Normalised gate trigger current IGT(Tj)/ IGT(25C), versus junction temperature Tj. IL(Tj) IL(25 C) Fig.10. Typical and maximum on-state characteristic. 3 2.5 TRIAC 10 Zth j-mb (K/W) BT136 unidirectional bidirectional 1 2 1.5 1 0.5 0 -50 0.01 10us 0.1ms 1ms 10ms tp / s 0.1s 1s 0.1 P D tp t 0 50 Tj / C 100 150 10s Fig.8. Normalised latching current IL(Tj)/ IL(25C), versus junction temperature Tj. IH(Tj) IH(25C) Fig.11. Transient thermal impedance Zth j-mb, versus pulse width tp. 3 2.5 2 1.5 1 0.5 TRIAC 0 -50 0 50 Tj / C 100 150 Fig.9. Normalised holding current IH(Tj)/ IH(25C), versus junction temperature Tj. December 1998 5 Rev 1.000 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation MECHANICAL DATA Dimensions in mm Net Mass: 1.1 g 6.73 max 1.1 BTA204S series D, E and F BTA204M series D, E and F seating plane 2.38 max 0.93 max 5.4 tab 4 min 6.22 max 10.4 max 4.6 2 1 2.285 (x2) 0.5 min 0.5 0.3 0.5 3 0.8 max (x2) Fig.12. SOT428 : centre pin connected to tab. MOUNTING INSTRUCTIONS Dimensions in mm 7.0 7.0 2.15 2.5 1.5 4.57 Fig.13. SOT428 : minimum pad sizes for surface mounting. Notes 1. Plastic meets UL94 V0 at 1/8". December 1998 6 Rev 1.000 Philips Semiconductors Product specification Three quadrant triacs guaranteed commutation DEFINITIONS Data sheet status Objective specification Product specification Limiting values BTA204S series D, E and F BTA204M series D, E and F This data sheet contains target or goal specifications for product development. This data sheet contains final product specifications. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information Where application information is given, it is advisory and does not form part of the specification. (c) Philips Electronics N.V. 1998 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights. LIFE SUPPORT APPLICATIONS These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale. December 1998 7 Rev 1.000 Philips Semiconductors - a worldwide company Argentina: see South America Australia: 3 Figtree Drive, HOMEBUSH, NSW 2140, Tel. +61 2 9704 8141, Fax. +61 2 9704 8139 Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 1 60 101 1248, Fax. +43 1 60 101 1210 Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6, 220050 MINSK, Tel. +375 172 20 0733, Fax. +375 172 20 0773 Belgium: see The Netherlands Brazil: see South America Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor, 51 James Bourchier Blvd., 1407 SOFIA, Tel. +359 2 68 9211, Fax. +359 2 68 9102 Canada: PHILIPS SEMICONDUCTORS/COMPONENTS, Tel. +1 800 234 7381, Fax. +1 800 943 0087 China/Hong Kong: 501 Hong Kong Industrial Technology Centre, 72 Tat Chee Avenue, Kowloon Tong, HONG KONG, Tel. +852 2319 7888, Fax. +852 2319 7700 Colombia: see South America Czech Republic: see Austria Denmark: Sydhavnsgade 23, 1780 COPENHAGEN V, Tel. +45 33 29 3333, Fax. +45 33 29 3905 Finland: Sinikalliontie 3, FIN-02630 ESPOO, Tel. +358 9 615 800, Fax. +358 9 6158 0920 France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex, Tel. +33 1 4099 6161, Fax. +33 1 4099 6427 Germany: Hammerbrookstrae 69, D-20097 HAMBURG, Tel. +49 40 2353 60, Fax. +49 40 2353 6300 Hungary: see Austria India: Philips INDIA Ltd, Band Box Building, 2nd floor, 254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025, Tel. +91 22 493 8541, Fax. +91 22 493 0966 Indonesia: PT Philips Development Corporation, Semiconductors Division, Gedung Philips, Jl. Buncit Raya Kav.99-100, JAKARTA 12510, Tel. +62 21 794 0040 ext. 2501, Fax. +62 21 794 0080 Ireland: Newstead, Clonskeagh, DUBLIN 14, Tel. +353 1 7640 000, Fax. +353 1 7640 200 Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053, TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007 Italy: PHILIPS SEMICONDUCTORS, Via Casati, 23 - 20052 MONZA (MI), Tel. +39 039 203 6838, Fax +39 039 203 6800 Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108-8507, Tel. +81 3 3740 5130, Fax. +81 3 3740 5057 Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL, Tel. +82 2 709 1412, Fax. +82 2 709 1415 Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR, Tel. +60 3 750 5214, Fax. +60 3 757 4880 Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905, Tel. +9-5 800 234 7381, Fax +9-5 800 943 0087 Middle East: see Italy Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB, Tel. +31 40 27 82785, Fax. +31 40 27 88399 New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND, Tel. +64 9 849 4160, Fax. +64 9 849 7811 Norway: Box 1, Manglerud 0612, OSLO, Tel. +47 22 74 8000, Fax. +47 22 74 8341 Pakistan: see Singapore Philippines: Philips Semiconductors Philippines Inc., 106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI, Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474 Poland: Al.Jerozolimskie 195 B, 02-222 WARSAW, Tel. +48 22 5710 000, Fax. +48 22 5710 001 Portugal: see Spain Romania: see Italy Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW, Tel. +7 095 755 6918, Fax. +7 095 755 6919 Singapore: Lorong 1, Toa Payoh, SINGAPORE 319762, Tel. +65 350 2538, Fax. +65 251 6500 Slovakia: see Austria Slovenia: see Italy South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale, 2092 JOHANNESBURG, P.O. Box 58088 Newville 2114, Tel. +27 11 471 5401, Fax. +27 11 471 5398 South America: Al. Vicente Pinzon, 173, 6th floor, 04547-130 SAO PAULO, SP, Brazil, Tel. +55 11 821 2333, Fax. +55 11 821 2382 Spain: Balmes 22, 08007 BARCELONA, Tel. +34 93 301 6312, Fax. +34 93 301 4107 Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM, Tel. +46 8 5985 2000, Fax. +46 8 5985 2745 Switzerland: Allmendstrasse 140, CH-8027 ZURICH, Tel. +41 1 488 2741 Fax. +41 1 488 3263 Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1, TAIPEI, Taiwan Tel. +886 2 2134 2886, Fax. +886 2 2134 2874 Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd., 209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260, Tel. +66 2 745 4090, Fax. +66 2 398 0793 Turkey: Yukari Dudullu, Org. San. Blg., 2.Cad. Nr. 28 81260 Umraniye, ISTANBUL, Tel. +90 216 522 1500, Fax. +90 216 522 1813 Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7, 252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461 United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes, MIDDLESEX UB3 5BX, Tel. +44 208 730 5000, Fax. +44 208 754 8421 United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409, Tel. +1 800 234 7381, Fax. +1 800 943 0087 Uruguay: see South America Vietnam: see Singapore Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD, Tel. +381 11 62 5344, Fax.+381 11 63 5777 For all other countries apply to: Philips Semiconductors, International Marketing & Sales Communications, Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825 (c) Philips Electronics N.V. 1999 Internet: http://www.semiconductors.philips.com SCA 68 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. Printed in The Netherlands 135002/1160/03/pp8 Date of release: December 1998 Document order number: 9397 750 06619 |
Price & Availability of BTA204M-800F
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |